-
The Epoch 24V 230Ah V2 is a premium 24V 230Ah LiFePO4 battery built for demanding marine, RV, off-grid solar, and trolling motor systems. This 5.89kWh lithium battery combines an IP67 dust-tight and immersion-rated case, internal self-heating, Bluetooth monitoring through the included battery gauge, Victron CANBus communication, and an 11-year limited warranty in one high-output Epoch V2 Elite Series platform.
Key Features
-
24V 230Ah V2 Elite Series LiFePO4 Battery (5.89kWh): 25.6V nominal, 230Ah and 5,888Wh (5.89kWh) of nominal stored energy in one managed case with one BMS, so a large 24V house bank needs fewer interconnects and cleaner routing than a bank of smaller batteries. A deep-cycle battery for house power and energy storage, not engine starting.
-
Dimensions & Fit: 20.86" L x 8.65" W x 12.06" H (529.8 x 219.8 x 306.3 mm; the height includes the terminal posts), 97 lb (approx. 44 kg). Install it upright. Replacing a Group 8D lead-acid battery? Confirm tray fit, hold-down and lid clearance against these dimensions first; the optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately) fastens to the threaded inserts on the case.
-
Native VICTRON Communications: CAN bus at 500 kbit/s to a compatible Victron GX device (Cerbo GX, Ekrano GX or Cerbo GX Mk2). The battery reports its status and charge limits, and with DVCC on it sets the charge voltage and current limits of Victron chargers. The communication harness is included; set the DIP switches and GX settings per the manual.
-
Elite Performance Specifications: 110A continuous discharge and 110A continuous charge, about 2,816W DC at 25.6V before inverter losses. Peak discharge of 300A and up to 200A charge for short durations; the BMS disconnects at 280A discharge or 200A charge after 5 seconds. If an inverter's continuous DC input can exceed 110A, add batteries in parallel.
-
BLUETOOTH Battery Intelligence: Bluetooth through the included battery gauge. The Epoch Li-Ion app (iOS and Android) shows state of charge, voltage, current, cell voltages, temperatures, history and warnings, and installs firmware updates over the air. The battery has a power button, and a mountable ON/OFF switch and the mountable battery gauge are included.
-
HEATED For Extreme Climates: LiFePO4 cells must not be charged below 0°C (32°F). When a charger is connected and the cells are too cold, the BMS holds off charging while the internal heater, powered by the charge source, warms them; charging resumes at 5°C (41°F). With self-heating, charging is supported from -30°C (-22°F) ambient. Discharge works down to -20°C (-4°F).
-
IP67 Rated Enclosure: Dust-tight and protected against temporary immersion in up to 1m of water for 30 minutes. It is not rated for water jets, pressure washing or continuous submersion: install it where it stays dry in normal use, with all harness connectors fully seated.
-
Scalable Banks: Up to 16 batteries in parallel (3,680Ah, 94.21kWh) or up to 2 in series (51.2V nominal, 58.4V at full charge), using matched C24230A batteries of the same age, capacity and state of charge. Series-parallel arrays are not covered by the published DIP switch settings; contact Epoch before designing one.
-
Advanced Smart BMS & Certifications: Over/under-voltage, overcurrent, short-circuit and high/low temperature protection, and a 270A internal fuse (UL 60691). UL 1642, UL 9540A and IEC 62619:2022 cells; CE and RoHS. The internal fuse does not replace system protection: install a DC-rated fuse or breaker close to the battery positive.
-
3,500+ Cycle Life & 11-Year Warranty: 3,500+ cycles to 70% remaining capacity. Maintenance-free: no watering or equalizing, though regular inspection and 8–12 N·m terminal torque checks keep the system safe. Backed by an 11-year limited manufacturer warranty; register within 90 days of purchase.
Key Benefits
-
Run Large Inverters: About 2,816W DC continuous, before inverter losses
-
Charge in Freezing Temps: Self-heating charges from -22°F (-30°C) ambient
-
Monitor via Bluetooth: Live data in the Epoch Li-Ion app
-
Victron Compatible: Seamless system integration
-
11-Year Warranty: Limited manufacturer warranty
-
3,500+ Cycles: To 70% remaining capacity
Battery Intelligence
Bluetooth App Monitoring
Your whole system, in your pocket
Connect over Bluetooth through the included battery gauge to see state of charge, cell voltages, temperatures and alerts in the Epoch Li-Ion app, and to install firmware updates over the air.
Victron Integration
- State of charge
- Cell voltages
- Temperatures
- History and battery events
- Warnings and alerts
Built to talk to your Victron system
Native CAN communication at 500 kbit/s with compatible Victron GX devices: the battery reports its status and charge limits, and with DVCC on it sets the charge voltage and current limits of Victron chargers. The communication harness is included; set the DIP switches and GX settings per the manual.
- GX Device Support
- Remote Monitoring
- DVCC Charge Control
- Seamless Integration
- Victron Ready
Built to go further
-
11-year warranty: Limited manufacturer coverage
-
Victron ready: CANBus communication
-
Bluetooth app: Real-time monitoring
-
Self-heating: Cold-weather charging
-
Advanced BMS: Built-in protection
-
LiFePO4 safety: Stable lithium chemistry
The Ultimate 24V Power Solution: Key Features
A premium 24V marine lithium battery, off-grid 24V solar battery, 24V RV battery upgrade, and 24V trolling motor battery platform.
Native Victron Integration via CANBus
Use this Victron compatible lithium battery with compatible Cerbo GX, Ekrano GX, and other GX device installations. CANBus battery communication lets the BMS share battery data with the Victron system for smarter monitoring and DVCC-controlled charging when configured according to Epoch guidance.
Cold Weather Ready: Built-in Self-Heating
LiFePO4 cells must not be charged below 0°C (32°F). When a charge source is connected and the cells are too cold, the BMS holds off normal charging while the internal heater, powered by the charge source, warms the cells; charging resumes once they reach 5°C (41°F). With self-heating, charging is supported from -22°F / -30°C ambient, and discharge is available down to -4°F / -20°C without heating.
Smart App Monitoring via Bluetooth
Bluetooth through the included battery gauge connects to the Epoch Li-Ion app (iOS and Android), so users can monitor state of charge, voltage, current, cell voltages, temperatures, history and warnings directly from a smartphone, and install firmware updates over the air. With several batteries, the dashboard also shows bank totals, with a toggle between series and parallel views.
IP67 Enclosure & Rugged Durability
The sealed IP67 enclosure is dust-tight and protected against temporary immersion in up to 1 m of water for 30 minutes. It is not rated for water jets, pressure washing or continuous submersion, so in marine compartments, RV bays, off-grid cabins, and overland rigs install it upright and secured against vibration, where it stays dry in normal use, with all harness connectors fully seated.
Unmatched Power, Scalability & Safety
High-output performance for larger 24V loads and expandable energy banks.
Run Heavy Loads: 110A Continuous Discharge
With 110A continuous discharge (about 2,816W DC at 25.6V before inverter losses) and 300A peak discharge for short durations, the Epoch 24V 230Ah V2 supports 24V inverter systems, RV air conditioning, marine house loads, 24V trolling motors, and other properly designed high-demand systems. If an inverter’s continuous DC input can exceed 110A, add batteries in parallel so the current per battery stays within the rating.
Wire Up to 16 Batteries in Parallel
Scale from a single 5.89kWh lithium battery to energy storage banks of up to 16 batteries in parallel (3,680Ah, 94.21kWh). The V2 Elite platform can also support up to 2 batteries in series for a 51.2V nominal (48V-class) string when installed according to Epoch’s guidance. Series-parallel arrays are not covered by the published DIP switch settings; contact Epoch before designing one.
Certified Components & 11-Year Warranty
The V2 Elite platform includes advanced BMS protection, a 270A internal fuse (UL 60691), UL 1642, UL 9540A and IEC 62619:2022 cells, 3,500+ cycle life, maintenance-free operation, and an 11-year limited manufacturer warranty.
Replacing a Group 8D battery?
This battery is designed for high-capacity 24V deep-cycle energy storage, not engine starting. Confirm tray fit, hold-down and lid clearance against 20.86 × 8.65 × 12.06 in, and verify cable clearance, terminal layout, charger settings, inverter requirements, communication setup, and installation requirements before replacing an existing battery bank. The optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately) fastens to the threaded inserts on the case.
Victron-ready system communication
Built to communicate directly with compatible Victron GX devices.
The V2 Elite platform uses CANBus communication at 500 kbit/s so the battery BMS can share data with compatible Victron GX devices; with DVCC on, the battery sets the charge voltage and current limits of Victron chargers. For Victron installations, configure the communication harness, DIP switches, BMS-CAN or VE.Can port speed, DVCC, controlling BMS, and battery monitor according to Epoch setup instructions. Program every charge source, including Victron equipment, to Epoch’s recommended 24V charging settings so charging stays correct if CAN communication is lost; without a GX device, use lithium-compatible charging equipment programmed to the same settings.
IP67 enclosure protection
Dust-tight. Immersion-rated. Install it where it stays dry.
The IP67-rated enclosure is dust-tight and protected against temporary immersion in up to 1 meter of water for 30 minutes (IEC 60529). It is not rated for water jets, pressure washing or continuous submersion: in RV, marine, overland, and off-grid installations, mount the battery upright and secured, where it stays dry in normal use, away from standing water and spray, with protected cabling and all harness connectors fully seated.
Applications and use cases
- RV house power (24V systems)
- Camper vans and van life
- Travel trailers and fifth wheels
- Motorhomes and Class A or Class C coaches
- Overlanding and expedition vehicles
- Marine house power
- 24V trolling motors
- Marine electronics and fish finders
- Yachts and cruising boats
- Off-grid solar systems
- Solar battery banks and inverter systems
- Home energy storage and backup power
- Cabins and remote power systems
- Victron-based systems with a compatible GX device
- Communications backup
- Commercial fleet and specialty power systems
At a glance
- 230Ah capacity
- 5.89kWh stored energy
- 110A continuous output
- 300A short-duration peak
- IP67 immersion-rated
- 16x parallel ready
What Can It Run?
Planning estimates for a single 5.89kWh battery, using 80% of nominal energy (about 4,710 Wh).
| Load |
Estimated Run Time |
| 2,816W DC Load |
≈ 1.7 Hours (4,710 Wh ÷ 2,816 W) |
| 1,000W DC Load |
≈ 4.7 Hours (4,710 Wh ÷ 1,000 W) |
| 500W DC Load |
≈ 9.4 Hours (4,710 Wh ÷ 500 W) |
| 100W DC Load |
≈ 47 Hours (4,710 Wh ÷ 100 W) |
Estimates are for a constant DC load at the battery terminals and use 80% of nominal energy, a planning figure that leaves reserve for battery life and cold conditions. Inverter losses, cable losses and temperature reduce runtime.
Suitable For:
- 24V marine lithium battery systems for house banks, onboard electronics, and high-demand boat loads.
- 24V trolling motor battery systems where voltage, current, and runtime requirements match.
- 24V RV battery upgrade projects for motorhomes, fifth wheels, campers, and travel trailers.
- Off-grid 24V solar battery storage for cabins, remote sites, tiny homes, and backup power systems.
- Victron-based power systems using compatible GX devices and BMS-CAN communication.
- Group 8D lead-acid replacement applications where tray fit, hold-down, lid clearance, charging profile, ventilation, and system requirements are compatible.
Compare
| Model |
Capacity |
Energy |
Weight |
Bluetooth |
Heating |
Victron Ready |
| 12V 460Ah Elite |
460Ah |
5.89 kWh |
97 lbs |
Yes |
Yes |
Yes |
| 24V 230Ah Elite |
230Ah |
5.89 kWh |
97 lbs |
Yes |
Yes |
Yes |
| 48V 100Ah Elite |
100Ah |
5.12 kWh |
97 lbs |
Yes |
Yes |
Yes |
Certifications & Standards
-
IP67: Dust-tight, and protected against temporary immersion in up to 1 m of water for 30 minutes. Under IEC 60529 the first digit rates solids and the second rates water.
-
UL 1642: The UL standard for lithium cells. Each cell design is tested for fire and explosion risk under abuse before it is built into a pack.
-
UL 9540A: A UL test method that measures how a cell behaves if it goes into thermal runaway, and whether fire can spread to its neighbours. The data is used to design safer energy storage systems.
-
IEC 62619: The international safety standard for rechargeable lithium cells and batteries in industrial use, including stationary energy storage.
-
UL 60691: The UL standard for thermal-links: one-shot fuses that open when temperature climbs past a safe limit under a fault, cutting the circuit before anything overheats.
-
CE: The manufacturer's declaration that the product meets the European Union's health, safety and environmental requirements, which is required to sell it in the European Economic Area.
-
RoHS: Complies with the EU Restriction of Hazardous Substances directive, which limits lead, mercury, cadmium and other toxic materials in electronics.
Please Note: Deep-cycle battery for house power and energy storage, not engine starting.
Please Note: Replacing a Group 8D battery: confirm tray fit, hold-down and lid clearance against 20.86 x 8.65 x 12.06 in first.
Please Note: Install upright, secured against vibration, where it stays dry in normal use; not rated for water jets, pressure washing or continuous submersion.
Please Note: Series-parallel arrays are not covered by the published DIP switch settings; contact Epoch before designing one.
Please Note: The internal fuse does not replace system protection: install a DC-rated fuse or breaker close to the battery positive.
Please Note: If an inverter's continuous DC input can exceed 110A, add batteries in parallel.
Please Note: Program all chargers to the LiFePO4 settings so charging stays correct if CAN communication is lost.
Also available as: 24V 230Ah V2-T Elite Series | 24V 230Ah Essential Series
-
Specifications
General
Brand: Epoch Batteries
Model / SKU: C24230A
Product name: 24V 230Ah V2 Elite Series LiFePO4 Battery
Series: Epoch V2 Elite Series
Battery type: Heated Bluetooth LiFePO4 deep-cycle battery with Victron communication
Replacing a Group 8D battery: Confirm tray fit, hold-down and lid clearance against the dimensions below
Chemistry: LiFePO4 / lithium iron phosphate
Cell type: Prismatic LiFePO4
Cell configuration: 8S1P (230Ah cells)
Bluetooth: Yes — through the included battery gauge; Epoch Li-Ion app (iOS and Android)
Victron communications: Yes — CAN bus at 500 kbit/s to compatible Victron GX devices (BMS-CAN or VE.Can port)
Internal self-heating: Yes
External controls: Power button on the battery; mountable ON/OFF switch and mountable battery gauge included
Cycle life: 3,500+ cycles to 70% remaining capacity
Warranty: 11-year limited manufacturer warranty; register within 90 days of purchase
Voltage and Capacity
Nominal voltage: 25.6V (3.2V per cell)
Nominal capacity: 230Ah
Stored energy: 5,888Wh / 5.89kWh
Operating voltage range: 20.0V – 29.2V
Maximum charge voltage: 29.2V (3.65V per cell)
Minimum voltage: 20.0V (2.5V per cell)
Self-discharge: ≤3% per month
Current Ratings
Max continuous discharge: 110A
Peak discharge current: 300A (short duration)
Max continuous charge current: 110A
Max charge current, short duration: 200A
Nominal continuous output power: Approx. 2,816W DC at 25.6V nominal voltage, before inverter losses
Series and Parallel Configuration
Series connections: Maximum 2 batteries in series (51.2V nominal, 58.4V at full charge)
Parallel connections: Maximum 16 batteries in parallel; set the DIP switches for the bank
Maximum 24V parallel bank: Up to 3,680Ah / approx. 94.21kWh with 16 matched batteries
Victron daisy-chain support: Up to 16 batteries in parallel on one compatible Victron-integrated system
Series-parallel: Not covered by the published DIP switch settings; contact Epoch before designing one
Temperature
Charge temperature range: -30°C to 55°C / -22°F to 131°F ambient, with self-heating
Cell charge temperature range: 0°C to 55°C / 32°F to 131°F
Discharge temperature range: -20°C to 55°C / -4°F to 131°F
Storage temperature, up to 1 year: 0°C to 35°C / 32°F to 95°F
Storage temperature, up to 1 month: -20°C to 45°C / -4°F to 113°F
Best performance: 15°C to 25°C / 59°F to 77°F
Low-temperature charge protection: Yes: charging stops at 0°C and resumes at 5°C (cell temperature)
High and low temperature disconnects: Yes
Dimensions and Weight
Length: 20.86 in / 529.8 mm
Width: 8.65 in / 219.8 mm
Height: 12.06 in / 306.3 mm (including terminal posts)
Rounded product dimensions: Approx. 20.9 in L × 8.7 in W × 12.1 in H
Weight: 97 lbs / approx. 44 kg
Mechanical
Case material: ABS and PC blend
Case flame rating: UL94 V-0
Enclosure protection: IP67: dust-tight; temporary immersion to 1 m for 30 minutes. Not rated for water jets, pressure washing or continuous submersion
Terminal size: M8 threaded
Terminal torque: 8–12 N·m (71–106 lbf·in)
Internal fuse: 270A rated (UL 60691); 1,200A transient overload for 3 seconds
Mounting: Upright; threaded inserts for the optional Epoch V2 & V2-T Mounting Hardware (8D battery bracket, sold separately)
Recommended Charging Settings
Charger type: Lithium (LiFePO4) compatible, CC/CV; program every charge source, including Victron equipment, to these settings
Absorption voltage: 28.4V
Absorption time: At least 15 minutes per battery in the bank
Float voltage: 27.0V
Re-bulk voltage: 26.6V
Equalization: Off / disabled
Temperature compensation: Disabled / 0mV per °C
BMS high-voltage cutoff: 29.2V
Charge current: 110A maximum continuous per battery; 200A for short durations
Victron setup note: Turn DVCC on and set the controlling BMS and the battery monitor to Epoch on a compatible Victron GX device
BMS Protection and Compliance
BMS protections: Overcharge, over-discharge, over-current, short-circuit, high-temperature, and low-temperature charge protection
Overcharge protection: 3.65 ± 0.01V per cell (29.2V); release 3.45 ± 0.01V per cell (27.6V)
Over-discharge protection: 2.70 ± 0.05V per cell (21.6V); release 3.00 ± 0.05V per cell (24.0V)
Over-current protection: Charge 200A (release 125A) and discharge 280A, each after 5 seconds; short circuit 1,200A
Temperature protection: Charge: low 0°C (release 5°C), high 55°C (release 50°C). Discharge: low -20°C (release -17°C), high 55°C (release 50°C)
Self-consumption: 20mA powered on; 200µA powered off
Certifications / compliance: UL 1642, UL 9540A and IEC 62619:2022 cells; UL 60691 internal fuse (TEX150-R1N-XBZ); CE, RoHS
Shipping classification: UN 3480, Class 9
Quick specifications
Energy Capacity: 5.89 kWh
Continuous Output: 110A
Peak Output: 300A (short duration)
Max Charge Rate: 110A (200A for short durations)
Cell Configuration: 8S1P
Chemistry: LiFePO4
Voltage: 25.6V
Max Charge Voltage: 29.2V
Operating Voltage Range: 20.0 - 29.2V
Ah Capacity: 230Ah
Max Continuous Discharge Amps: 110A
Max Charge Current Amps: 110A (200A for short durations)
Max Discharge Peak Current Amps: 300A (short duration)
Series | Parallel: Max (2) in Series OR Max (16) in Parallel - 2S1P or 1S16P
Charge Temp Range: -30°C (-22°F) / 55°C (131°F) ambient, with self-heating
Discharge Temp Range: -20°C (-4°F) / 55°C (131°F)
Storage Temp: 0°C (32°F) / 35°C (95°F) for up to 1 year; -20°C (-4°F) / 45°C (113°F) for up to 1 month
Safety: BMS (Battery Management System) Over Voltage, Under Voltage, Over-Current, Short Circuit, Over Temperature, Under Temperature
Length: 20.86 in
Width: 8.65 in
Height: 12.06 in
Weight: 97 lbs
Additional information
Certification: UL 1642, UL 9540A, IEC 62619:2022 (cells)
Certification: UL 60691 (internal fuse, TEX150-R1N-XBZ)
Certification: CE, RoHS
Certification: UN 3480, Class 9 (transport)
In the Box
- 24V 230Ah V2 Elite Series battery (C24230A)
- Communication harness
- Mountable battery gauge (Bluetooth)
- Mountable ON/OFF switch
-
Recommended Charging Settings
Program every charge source to these settings, including Victron equipment, so charging stays correct if CAN communication is lost:
- Charger type: Lithium (LiFePO4) compatible, CC/CV
- Bulk / absorption voltage: 28.4V
- Absorption time: 15 minutes per battery in the bank (for example, 60 minutes for four batteries)
- Float voltage: 27.0V
- Re-bulk voltage: 26.6V
- Equalization: Disabled
- Temperature compensation: Disabled (0 mV/°C)
- Charge current: 110A per battery maximum continuous; size every charge source, and the total of all sources, to stay within it. The user guide lists 200A as the maximum for short periods; the BMS charge over-current protection acts at 200A after 5 seconds.
- BMS high-voltage cutoff: 29.2V. Never charge above 29.2V, and do not use lead-acid equalization, desulfation or repair modes.
- Charging temperature: 0°C to 55°C (32°F to 131°F) cell temperature; with self-heating, charging is supported from -30°C (-22°F) ambient. Below freezing the heater, powered by the charge source, warms the cells first, so expect a delay before charge current flows; charging resumes when the cells reach 5°C (41°F).
- Alternators: use a DC-DC charger, or an alternator regulator set up for lithium, and follow the alternator manufacturer's guidance.
Victron GX setup
- Set the DIP switches on every battery (see the user manual).
- Fit the harness plug with the waterproof bung into the Master battery's blue port.
- For a bank, run an RJ45 cable from the Master's black port to Slave 1's blue port, then from Slave 1's black port to Slave 2's blue port, and so on, up to 16 batteries in parallel.
- Plug the harness's grey RJ45 plug into the GX device's BMS-CAN port (Cerbo GX or Ekrano GX). On a Cerbo GX Mk2, use VE.Can 1 or VE.Can 2.
- If you use a VE.Can port, open Settings > Services > VE.Can on the GX device and set the port speed to 500 kbit/s.
- Switch on the batteries.
- On the GX device, turn on DVCC, set the controlling BMS to Epoch and set the battery monitor to Epoch.
- Check that the Epoch battery appears in the device list, that the number of modules online equals the number of batteries installed, and that the installed capacity (Ah) equals the bank capacity, for example 920Ah for four batteries.
- While charging (not while inverting), the inverter tile shows External control. Under DVCC the system charges to 28.4V, holds absorption for at least about 15 minutes per battery, then floats at 27.0V.
- Manually program the MultiPlus, Quattro and every other charge source to the settings above as a fallback.
-
MASSIVE Grand Design Solitude Dual Victron Inverter and Epoch lithium RV solar install
Riverstone Legacy with 6490 Watts of Solar, Big Battery Bank and Big Inverters
Toy Hauler goes off grid with Victron, Rich solar, and Epoch batteries!
How to Unleash the Power of Victron Comms with Epoch Elite V2 Batteries
Why the Epoch V2 Elite Series 460Ah Battery has NO competition!
-
C24230A Spec Sheet
C24230A User Manual
C24230A Technical Data Sheet
Internal Fuse UL 60691 Listing (TEX150-R1N-XBZ)
Safety Data Sheet (LiFePO4)
-
Does the Epoch 24V 230Ah V2 connect directly to my Victron system?
Yes. The battery communicates over CAN bus at 500 kbit/s with compatible Victron GX devices, including Cerbo GX, Ekrano GX and Cerbo GX Mk2 installations. The included communication harness has a grey RJ45 plug for the GX device’s BMS-CAN port; on a Cerbo GX Mk2, use VE.Can 1 or VE.Can 2 and set the port speed to 500 kbit/s. For a bank, RJ45 cables link each battery’s black port to the next battery’s blue port, up to 16 batteries in parallel. Set the DIP switches on every battery, then turn on DVCC and set the controlling BMS and the battery monitor to Epoch: the battery then reports its status and sets the charge voltage and current limits of Victron chargers.
How does the self-heating feature work in freezing weather?
LiFePO4 cells must not be charged below 0°C (32°F). When a charge source is connected and the cells are too cold, the BMS holds off normal charging while the internal heater, powered by the charge source, warms the cells. Charging resumes automatically when the cells reach 5°C (41°F), so expect a delay before the state of charge starts to rise. With self-heating, charging is supported from an ambient temperature as low as -22°F / -30°C, and discharge is available down to -4°F / -20°C without heating.
Can I connect these 24V batteries in series or parallel?
Yes. The Epoch 24V 230Ah V2 Elite battery supports up to 16 batteries in parallel for a 24V bank of up to 3,680Ah (94.21kWh), or up to 2 batteries in series for a 51.2V nominal (48V-class) string that reaches 58.4V at full charge, so every charger, inverter, fuse, switch and conductor must be rated for the string voltage. Use matched C24230A batteries of the same age, capacity, and state of charge, set the DIP switches for the bank, and follow Epoch’s installation and communication setup instructions. Series-parallel arrays are not covered by the published DIP switch settings; contact Epoch before designing one.
Is the Epoch 24V 230Ah battery suitable for marine environments?
Yes, for marine house banks, yachts and cruising boats, 24V trolling motors and marine electronics. The IP67 enclosure is dust-tight and protected against temporary immersion in up to 1 m of water for 30 minutes, but it is not rated for water jets, pressure washing or continuous submersion. Install the battery upright and secured against vibration and wave impact, in a dry, ventilated location away from standing water and spray, with protected cabling and all harness connectors fully seated. It is a deep-cycle battery, not a cranking battery for engine starting.
What size inverter can a single 24V 230Ah V2 battery run?
A single battery is rated for 110A continuous discharge, about 2,816W DC at 25.6V before inverter losses. The DC input current is roughly the AC load divided by (battery voltage × inverter efficiency): a 2,000W load through an inverter assumed to be 90% efficient draws about 2,000 ÷ (25.6 × 0.90) ≈ 87A. If the inverter’s continuous DC input can exceed 110A, add batteries in parallel so the current per battery stays within the rating, and size cables, fusing and the disconnect for the maximum system current.
What information does the Epoch Bluetooth app provide?
Bluetooth runs through the included battery gauge and connects to the Epoch Li-Ion app (iOS and Android), where the battery appears as C24230A_ followed by its serial number. The dashboard shows state of charge, voltage, current, power, remaining capacity and warnings for each battery, and bank totals with several batteries. The Cells screen shows each cell’s voltage, the cell balance and the temperature readings; History graphs voltage, current, state of charge, capacity and temperature; Battery events logs BMS protections; and the About page installs firmware updates over the air. Bluetooth range is typically about 10 m (33 ft).
-
Epoch Batteries Limited Warranty
11-Year Limited Warranty: 5 Years Free Repair or Replacement
- Years 1–5: free repair or replacement (Epoch chooses which)
- Years 6–11: 40% off MSRP on a replacement battery
Epoch Batteries warrants this product to the original end-user purchaser to be free from defects in materials and workmanship under normal use and service for the warranty period above, when it is installed, operated, charged, stored and maintained as its manual describes. The warranty is not transferable and ends if the product is sold or given to someone else.
How the 40% Discount Works
After the free coverage ends and through Year 11, if the battery has a covered defect Epoch offers a new replacement of the same model (or a current Epoch model of equal or greater capacity and function) at 40% off Epoch's MSRP on the date of the offer. The offer covers one replacement per defective battery, bought directly from Epoch, and you pay the discounted price, any tax and shipping.
When Coverage Starts
Coverage starts on the date of your original purchase. To confirm that date, register the product with Epoch within 90 days of purchase or keep your proof of purchase (an invoice or receipt showing the product, purchase date and seller). If you can provide neither, coverage starts on the manufacturing date recorded for the product's serial number. A repaired or replacement product is covered for the rest of the original warranty period.
What Is Not Covered
The warranty covers defects in materials and workmanship only. It does not cover damage or failure caused by installation, wiring or system design that doesn't follow the manual (including undersized or damaged cables, poor crimps, loose or corroded connections and incorrect fusing); reverse polarity, short circuits or faults in the connected electrical system; series or parallel connections beyond the manual's limits, or mixing batteries of different models, capacities, ages or states of charge; a product not secured as the manual requires; charging outside the manual's voltage, current or temperature limits; discharge above the rated current, or engine starting with a battery not listed as a starting or dual-purpose battery; over-discharge, storage fully discharged, or storage for more than 3 months without recharging; accidents, impact, fire, flood, power surges, submersion or exposure beyond the product's IP rating; opening, modification or repair by anyone other than Epoch or an Epoch-authorized provider; removed or altered serial numbers; normal capacity loss and wear consistent with age and use; or cosmetic damage that doesn't affect performance. Using chargers and other equipment from other brands does not affect coverage by itself.
Obtaining Warranty Service
Start a claim through the Epoch Warranty Portal before the warranty period ends, with the model, serial number, proof of purchase or registration, a description of the problem and any photos, videos or app screenshots. If the claim qualifies, Epoch issues an RMA number with packing and shipping instructions; do not ship a product without an RMA. Epoch inspects and tests the product, typically within 3–10 business days after it arrives, and then repairs or replaces it, or makes the discount offer where applicable.
Shipping
You pay to ship the battery to Epoch; Epoch pays to ship an approved warranty repair or free replacement back to you. For discount replacements you pay shipping on the replacement battery. Packaging must follow the RMA instructions (lithium batteries are regulated hazardous materials in transport).
Visit Epoch's Warranty Page to review the complete warranty terms (effective October 17, 2026).
-
Shipping is typically through freight carriers and the actual shipping time is contingent on your location and the specific warehouse dispatching your order. Please allow for a 1-3 business day processing period before shipment, and an estimated delivery time of up to 7 business days. Your confirmation email will include delivery details and we will send you a tracking number as soon as one is available. If you ordered several separate items, you may receive multiple tracking numbers. Once the item has been shipped, the freight service will contact you to coordinate the date and time of delivery. If you require any special accommodations during delivery please let us know as soon as possible and let the delivery company know when arranging the appointment.
Typically, orders will be dropped off either curbside or outside your front door or garage. It is your responsibility to bring the order inside or to its final destination and to remove any existing items.
Depending on the item, parts may be shipped in multiple boxes, and assembly may be required. When your order is delivered, please check that you have all pieces of the item and that nothing is damaged. If your order is damaged during transit and external damage is visible, note the damage immediately, write it on the delivery documents, take photos and/or videos, and refuse shipment. If there is no visible external damage, accept the package but note “subject to concealed damage” on the delivery documents. Any damage upon delivery needs to be reported within 24 hours of delivery or you may not be eligible for a refund. For additional information on submitting claims, as well as incorrect item exchanges, and replacements, please see our Refund Policy.
For more information about shipping, please visit our complete Shipping Policy.
-
Why Shop With Eco Emperor?
At Eco Emperor, our mission is to empower you to lead a sustainable and fun lifestyle with ease and confidence. Whether you're upgrading your outdoor experience or enhancing your eco-conscious journey, here’s why choosing us is a decision you can feel great about:
Expert and Customized Care
Our knowledgeable and friendly team is here to support you every step of the way. We pride ourselves on providing personalized service and swift responses to ensure a smooth and satisfying experience. Our dedicated team is available via phone, email, and live chat to provide you with prompt and helpful support.
Authorized Retailer of High-Quality, Trusted Products from Leading Brands
We partner with the best brands in the industry to bring you reliable, high-quality products. As authorized retailers, we guarantee authenticity and offer full manufacturer warranties on every item. You can trust that our products are built to last and perform efficiently.
Free & Fast Shipping
We know you’re eager to begin your new products or start your next outdoor adventure. That’s why we prioritize quick, reliable, and free shipping to get your orders to you on time and in perfect condition.
Competitive Pricing
We believe that sustainable living should be accessible to everyone. We offer competitive pricing on all our products, so you can enjoy high-quality eco-friendly solutions and outdoor products without breaking the bank.
Choose Eco Emperor for all your outdoor and eco-friendly product needs, and become part of a movement that’s embracing a more sustainable and adventurous lifestyle.
Thank you for supporting a greener, cleaner future, while enhancing your outdoor experiences and powering your adventures.💚
![Sok Battery 12V 206Ah Lithium Iron Phosphate (LiFePO4) Solar Battery SK12V206P [Marine Grade]](https://cdn.shopify.com/s/files/1/0806/0803/5119/files/Sok-Battery-12V-206Ah-Lithium-Iron-Phosphate-_LiFePO4_-Solar-Battery-SK12V206P-_Marine-Grade_250x250.jpg?v=1696275766)
![Sol-Ark 15K 120/240/208V 48V [All-In-One] Pre-Wired Hybrid Solar Inverter (UL: Sol-Ark-Limitless 15K-LV)](https://cdn.shopify.com/s/files/1/0806/0803/5119/files/Sol-Ark-15K-120_240_208V-48V-Hybrid-Solar-Inverter-UL-Sol-Ark-Limitless-15K-LV_250x250.jpg?v=1708309305)
